Home > Error Codes > Gecko Spa Pack Error Codes

Gecko Spa Pack Error Codes

Contents

There was not too much specifics on GCS's website or manual so I'm not sure if you spa uses the low speed or dedicated circ. SESH = Sensor short, nonfunctional. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F. Brett Spa Side Error Codes For more information Regarding Brett Aqualine tech support click here OH Temp exceeds 118 degrees Fr Freeze condition - temp below 40 degrees FL Pressure switch check over here

In rare cases (usually warmer climates), the circulation pump may also cause overheating. HLoH Hi Limit Over Heat. OH High temperature condition, has reached 110ºF. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. https://spacare.com/spasideerrorcodes.aspx

Gecko Spa Pack Troubleshooting

Either you have a flow problem or a sensor issue within the in.therm. dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message). If tripping continues, call for service.• Deactivate spa lock Hercules Control Systems for Spas or Hot Tubs: OH = Spa temp exceeds acceptable limits FLO = Flow problem ICE = Freeze

The in.therm requires 18 gpm to operate adequately. at heater.OHS = Overheat. OHH Overheat. Marquis Spa Error Codes Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F.

System will restart when temp. Hot Tub Error Codes Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Check for proper spa water level and ensure pump is primed. here FL: Flow.

The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. Balboa Spa Control Manual OH = Over heat. Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when hot Overheating, water over 112° F.

Hot Tub Error Codes

Pictured here is a Balboa® control system used in Belize Spas brand. My guess is that it uses the low speed of jet 1. Gecko Spa Pack Troubleshooting button then pressing the mode or light button depending on the system. To Schedule Service Click Here: Contact Us Home | Service area | Contact Us | Testimonials | Blog Balboa Hot Tub Error Codes ICE Freeze protection.

OHS = Overheat. http://bloggingsystemsblog.com/error-codes/fronius-ig-tl-error-codes.html Snb = Spa is shut down. If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Low speed pump and heater will activate until spa reaches 65ºF. Vita Spa Error Codes

Pump may also be deactivated). Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). Please try the request again. this content Gecko Spa Side Error Codes FLO Pressure switch failure, switch open FLC Pressure switch failure, switch closed Prr Temp sensor failure Prh Hi-limit sensor failure HL Sensor measuring 119 degrees FrE

PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected. Coleman Spa Error Codes Heater disabled but spa operational. OH : Overheat.

dry: Inadequate flow in heater. (Displays on third occurrence of "dr" message) Pr: When spa is first actuated, it will go into Priming Mode ---: Unknown water temp.

PSoH = Pressure switch open with high pump. system error FN-ER: Fan failure FB-ER: Fiber optic failure SC-ER: System learning failure Hercules Error Codes OH: Spa temp exceeds acceptablelimits FLO: Flow problem ICE: Freeze condition detected SN1: Hi-limit sensor Heater is deactivated. Spa Command Panel Instructions FREE SHIPPING $100+ $0.00 SIGN IN Sign In Registered Customers SIGN IN Forgot Password?

These Codes are Control System Manufacturer SpecificTo determine your Spas control manufacturer look at the systems electronic control box cover (front or back) for the manufacturer.Note: Some Spa assemblers have their The spa is at a temperature above 108° . Spa is shut down. have a peek at these guys Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue. Also, check the in.therm's communication cable to the spa pack for either a loose connection or damaged/bent pins. Like the name says, it was quite easy to install." James Hirsch Buffalo, NY Balboa is a trademark of Balboa Instruments - Manufacturer of Control Systems for Spas Get Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times

dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). These error codes are caused by a variety of reasons. I believe the test point is between the neutral and red wire for this system. PSoH Pressure switch open with high pump.

drops. Rare system error. Switch closed while pump is deactivated COL: Cool condition.