Home > Error Code > Fronius Inverter Error Codes

Fronius Inverter Error Codes

Contents

Posts: 25,609Super Moderators admin August 12 #4 Thank you Mark for the information.-Bill Near San Francisco California: 3.5kWatt Grid Tied Solar power system+small backup genset0 Sign In or Register to comment. STATE 566 Arc detector switched off (e.g. Code Description Behaviour Remedy STATE 502 Insulation error on the solar panels Warning message is shown on the display If this STATE code keeps recurring, contact your solar power system installer. Clean solar panels or remove snow 2. http://bloggingsystemsblog.com/error-code/fronius-inverter-error-104.html

Code Description Possible causes Remedy (sequence) STATE 501 Heat sink temperature too high, although Fronius IG is on low output 1. Error is remedied automatically 2. Checkout the below. Generated Thu, 24 Nov 2016 02:46:54 GMT by s_mf18 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection http://www.fronius.com/cps/rde/xchg/SID-75B7D5A5-D0CD0E9D/fronius_usa/hs.xsl/2714_2191.htm

Fronius Ig Plus Error Codes

STATE 445 Invalid limit value settings The inverter is not feeding any energy into the grid for safety reasons. STATE 758 Internal error: Real Time Clock module is in emergency mode Time may be inaccurate or lost (feeding energy into the grid normal).. after a PC board has been replaced) Update the inverter software; if the STATE code persists contact your local Fronius Service Partner STATE 482 Startup incomplete Perform AC reset (turn AC

Connect Fronius IG inverter to another phase 3. If you are not in the Gold Coast / Brisbane area please contact Fronius Tech Support on 03 8340 2910 View Fronius IG Inverter Manual Here When a Fronius inverter has If problem persists contact your Fronius Service Partner STATE 415 No END-enabling signal despite release by IG-control Internal fault If problem persists contact your Fronius Service Partner STATE 416 Communication error Fronius State 509 Update inverter firmware; if this status code is displayed all the time please contact your local Fronius Service Partner.

Internal fault STATE 308 Intermediate circuit voltage out of the maximum limit 1. Fronius Primo Error Codes Click Here. If the STATE code is displayed all the time notify your local Fronius Service Partner. If problem persists contact your Fronius Service Partner 3.

If problem persists contact your Fronius Service Partner STATE 511 Errors detected by LocalNet Sensor Card self diagnostic system STATE 512 According to the device type too many power stacks have Fronius Primo State 241 Finding the error causing the STATE 516 warning message To further locate the cause of the STATE 516 warning message you need to do the following: Go to the SETUP menu What does this mean?This probably indicates a DC voltage in excess of 500V at the unit. Click on the picture to hear an audio file of the word.

Fronius Primo Error Codes

Code Description Behaviour Remedy STATE 301 Overcurrent (AC) Short-term interruption while feeding energy into the grid due to over current in the inverter. Internal fault 1. Fronius Ig Plus Error Codes Internal fault 1. Fronius Inverter Tech Support If problem persists contact your Fronius Service Partner STATE 443 DC-DC energy transfer failure.

Code Description Possible causes Remedy (sequence) STATE 201 Grid voltage is higher than the specified limit 1. check over here Internal fault 1. In case of a temperature excess additional cooling down phase is maintained. STATE 517 Derating caused by too high a temperature When power derating occurs, a warning message is shown on the display Purge cooling air openings and heat sink if necessary; fault Fronius State 240

Where can I look up the meaning of an error code on the display?The operating instructions contain a list of all the error codes that can occur while the unit is Click Here For Answers! Can you add more solar panels to your solar power system? Simon RogersPost authorMarch 13, 2016 at 7:17 amPermalink Hi Steve, thanks for your enquiry. http://bloggingsystemsblog.com/error-code/fronius-inverter-error-516.html Find out more about Fronius STATE 104 error codes here 1.

Either way we will require your inverters serial number which can be found underneath the inverter. Fronius Error State 241 This means that the first power stage set (PS00) is on Standby mode - it's not producing any power. Looking for a Fronius SYMO State Code?

Grid frequency error on the public mains 2.

And inspect (and tighten with a screw driver) all AC connections from inverter back to the Branch circuit/breaker connections.-Bill "my guess" B. This ten-digit number is the serial number of your inverter. The first thing to try with this code is an update of the inverter software, you can find this here. Fronius Error Code 240 If you are on the Gold Coast or South Brisbane and your Fronius Primo inverter is giving you problems then contact us here or give us a call on 07 55

Normally the shutdown procedure will be as follows. 1. Fault is rectified automatically; if this STATE code occurs when there is sufficient insolation (sunlight) contact your solar power system installer. Internal fault 1. weblink STATE 437 Power stage set problem STATE 438 Functional incompatibility (one or more PC boards in the inverter in the inverter are not compatible with each other, e.g.

Internal fault 3. Fronius Rapid Shutdown Box Single and Multi Manual MULTI Fronius Rapid Shutdown Box Single and Multi Manual Fronius Datamanager 2.0 Manual EA Fronius Datamanager 2.0 Operating Manual Fronius Primo Click Here. If the fault continues please contact your local Fronius Service Partner for further assistance.

Locate the PV ARRAY MAIN SWITCH / SOLAR DC ISOLATOR (usually right beside the inverter) and switch it OFF The inverter will turn off after a few seconds, wait 30 seconds The displayed energy is calculated from the measured current and the measured voltage and is intended to provide an overview of the amount of energy supplied. Before we can provide any advice we will require your inverters serial number which can be found underneath the inverter. As always, our Fronius Technical Support is here to help you, so please feel free to contact us with your needs.

Need more information on Fronius solar inverters? Automatic correction 2. Change values in the service menu 3. The Fronius inverter reacts by disconnecting from the grid and attempts to switch on again after the specified mains monitoring period, as long as no further errors occur during this period.

Mains voltage error 2.