Home > Error Code > Frigidaire Electric Range Error Code F10

Frigidaire Electric Range Error Code F10

Contents

Submit Your Work! Wire nuts (pack of 10) AP5641944 Good luck and keep us posted. I am lost as to how to proceed next as the touchpad was included with the new EOC? I have replaced the EOC and the RTD, and still get the error code, what else could it be :(? this contact form

If the fault returns, replace the keyboard ( membrane ). If resistance does not match the chart, replace the RTD sensor probe. Cut off the wires at the plug which goes to the EOC, leaving about 3″ to 4″ to splice a new wires. Resistance Check If the probe appears to be intact, it could be broken internally and giving faulty information.

What Does F10 Mean On A Frigidaire Oven

Reproducción automática Si la reproducción automática está habilitada, se reproducirá automáticamente un vídeo a continuación. Mike // Jun 6, 2015 at 7:05 pm Hi Gene, I have a PLES389ECE showing F30. Bad Micro Identification. None of the control panel would stop it, so we had to flip the breaker.

The part number for the temperature probe is 316217002 The part number for the EOC is 318414213 Good luck. In such situation the solution is to replace the Electronic Oven Control (EOC). Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question. Frigidaire Gas Range F11 Error Code LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 01-04-2014, 10:08 AM ronusmc Junior Member Join Date: Jan 2014 Posts: 2 Frigidaire Stove F10 Error Brand: FrigidaireAge:

Kenmore and Craftsman model numbers typically have three digits separated by a period. Frigidaire Oven F10 Beeping What Does the F10 Code Mean on a Frigidaire Electric Range? In regards to my Electrolux Icon electric wall oven E30EW75GPS1 In addition to the broiler coming on all by itself and this overheating the oven, we also noticed sometimes during baking http://www.shopyourway.com/questions/1027720 Per your advice (regarding Frigidaire stove model LFGF3014LWC), I cut the plastic connectors off and spliced the wires together making sure that the violet wires from the EOC side matched the

Thank you. Frigidaire Rtd Sensor It has to be exchanged under the part warranty. So the only solution is to replace the EOC. Gene.

Frigidaire Oven F10 Beeping

Thank you for your question. http://www.applianceblog.com/mainforums/threads/20659-FIXED-error-f10-shut-breaker-off-now-oven-normal Get help locating it Login|Contact Us Appliance Need Appliance Repair Help? What Does F10 Mean On A Frigidaire Oven Gene. Frigidaire Oven F10 Reset Otherwise the EOC is the culprit.

Thanks, Gene // Sep 7, 2015 at 9:26 pm Hi Jay, Thank you for your question. http://bloggingsystemsblog.com/error-code/frigidaire-range-error-code-f1.html There suppose to be one more letter at the end. Please help! You can determine it by visual EOC inspection and/or by the wiring diagram for your oven (if it is available). Frigidaire Eoc

I dont know model number but do think the stove could have shorted out and it ave a f10 code Gene // Dec 19, 2014 at 8:29 pm Hello Darlene, The Ken // Dec 29, 2014 at 9:59 am Hello Gene, Thank you, you always answer quickly. I ran the self clean on my electrolux and within 2 weeks of using my oven again, I had the F10 runaway temperature alarm. http://bloggingsystemsblog.com/error-code/ge-profile-electric-range-error-code-f2.html Gene.

We'll help you figure it out! Frigidaire Oven Error Codes Disconnect the wire harness from the sensor. AskGene.com front page archives about RSS ← GE refrigerators thermistors values Whirlpool, KitchenAid or Kenmore tall tub dishwasher door squeaking → How to fix Frigidaire oven error code F10, F11, F30,

the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below.

Sorry for such sad news. There is a separate membrane switch in your range which would need to be replaced in such situation. If you would like to replace it too, I need one more letter from the model number to get the correct part number for you. F10 Error Code Kenmore Oven When I searched for a part it appears you can't just replace the ribbon connector, but have to replace the whole TST panel ($600!!).

Your question was published, help is on its way! If the problem persists, replace the EOC. Very new range. his comment is here If this fault code appears when the oven is at room temperature, then the failure points to a failed oven temperature sensor probe circuit or a bad electronic oven control board.

Gene // Dec 24, 2014 at 5:31 pm Hi Ken, Merry Christmas and Happy New year to you as well! Browse by Appliance Dishwasher Dryer Freezer Garbage Disposer Microwave Range Hood Range / Oven Refrigerator Trash Compactor Washer Browse by Brand Amana Parts Bosch Parts Dacor Parts Frigidaire Parts Hotpoint If your Frigidaire electric range senses that the temperature is going beyond acceptable limits, the F10 code will display and the range will automatically shut off to prevent damage. Model retention may be affected by your browser settings.

My issue has not changed. Thank you for your question. It's fast and easy to create one. Thank you Gene // Nov 5, 2014 at 11:41 pm Hello Frank, Thank you for your question.

What should I focus on next? Maximum oven door unlock attempts exceeded. Melted the teflon off a baking pan. F10 is a common error code for several manufacturers that appears when your oven exceeds the temperature you set it at in either the cook cycle or the clean cycle.

In such situation the only solution is to replace the EOC. Thank you for your question. Sad news. This error code indicates a failed potentiometer for LF burner, a user interface board or the harness between the mother board and the user interface boards.

My frigidaire oven goes beep, beep, beep!!! - youtube, My frigidaire oven goes beep, beep, beep. Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try. When I used the oven the next day to heat taco shells, it got really hot (burnt them to chars!) and then the F10 code went off again- this time I Save model in your profile permanently Don't have a profile?

the fault code "f10" indicates a runaway oven temperature.